Health

How to fix a Toilet That Drains Slowly

Are you wondering how to fix a toilet that drains slowly? Then, read the article.

You probably won’t even need to call a plumber to fix a toilet that drains slowly. Depending on the cause, there may be a number of solutions available for unclogging a toilet that drains slowly.

Here are some methods, from the simplest to the most complex, for fixing a clogged toilet:

Use baking soda and vinegar to dissolve the clog.

However, vinegar is a weak acid while baking soda is an alkali. When mixed, the two inexpensive and easily accessible items bubble and explode with explosive force.

The clog in the P-trap or drain line is broken down as the two substances react with one another. If the clog is caused by something like toilet paper, soap, or calcium deposits, this method often proves effective.

If you don’t have any baking soda, you can use borax instead. In comparison to baking soda, borax has far more strength.

To remove a clog from a toilet, mix baking soda and vinegar as shown below:

Spill no more water into the basin. Since you don’t want the clog remedy to be diluted by water at the bottom of the bowl, draining it is the first step.

  • Add one cup of baking soda to the bowl.
  • Slowly incorporate 2 cups of vinegar.
  • Don’t rush the solution; give it fifteen minutes to take effect. In the meantime, get some water on to boil.
  • To fill the bowl, pour in one gallon of boiling water. By dissolving any remaining blockage and flushing the broken down clog down the drain, water will assist clear the drain. Boiling water will damage the bowl, so stick to hot water instead.

Make use of hot water and dish soap.

This is yet another effective strategy for clearing a clogged toilet without the use of a plunger or snake. What you should do next is as follows:

  • You can remove the water from the bowl’s base by using a sponge. Put on some gloves, that’s all I’m asking.
  • Put half a cup of dishwashing liquid in the toilet.
  • Hurry and bring roughly a gallon of water to a boil in the kitchen.
  • Just pour the water into the dish and let it sit for a while.
  • After waiting 30 minutes, flush the toilet to see whether the water drains faster.
  • A few attempts may be necessary to permanently resolve the issue
  • If a blockage in the toilet’s trap or drainpipe was caused by, say, a bar of soap or toilet paper, running hot water over the area can help break up the clog into tiny pieces, allowing the water to flow more freely and unclogging the toilet.

Use plunger

To remove obstructions from the toilet trap or drainpipe, a plunger is an efficient instrument. The method is effective because it uses a pressure differential to break up the clog, with higher pressure at the top than at the bottom.

In doing so, you are helping the blockage go further down the drainpipe and restoring normal flow to your toilets.

Make sure you have a plunger that fits your toilet. Two distinct varieties of plungers exist. Plungers with a flat bottom and bell-shaped plungers. In this case, a bell-shaped plunger is the best choice.

It fits snugly around the hole of the toilet bowl, preventing any water from leaking out and allowing you to flush with full force.

How to Use a Plunger to Clear Clogs in a Toilet

It might be helpful to pour some water into the dish. The plunger can only work properly if it is submerged.
Holding the plunger over the opening of the toilet bowl, make sure it completely seals the aperture to fix a toilet. People have reported better results after applying Vaseline around the plunger’s rim.
Get down to business and dive in. To create a good seal between the plunger and the opening of the toilet bowl, the first plunge should be rather light. For the next five minutes after the initial dive, dive aggressively.

Use auger to fix a toilet with slow drain

It is possible to remove clogs from a toilet by using a toilet auger, often known as a plumber’s snake, which works by either shredding the clog into tiny pieces or drawing it out entirely. It’s equipped with a flexing cable and a cranking handle in addition to its helical and hooked head.

It’s important to be careful when using a toilet auger since it can cause serious scratches in your toilet bowl if you’re not. The head may be introduced and removed from the bowl without ever touching the surface, thanks to the included protective guide.

The following is a guide for using a toilet auger to clear a clogged toilet.

  • Draw the cable in until the auger’s tip is level with the lid of the bowl.
  • Carefully place the auger over the opening of the bowl as you lower it inside.
  • Get started forcing the cable down the drain until you meet resistance.
  • Turn the handle counterclockwise until you reach the limit. If it seems too challenging, try turning the handle in the opposite direction and giving it another try.
  • If the obstruction proves too difficult to traverse, you can always pull the cable within the tube and release the bowl guide and tube without touching the bowl’s interior.
  • If you are successful in removing the obstruction, flush the toilet to see if the water drains as it should. If that doesn’t work, try re-inserting it.
  • See this post for details on using a plunger to clear a clogged toilet.

Clear the vent stack of debris.

When a clogged vent is the cause of problems with the toilet or other plumbing fixtures, fixing the problem is simple. In order to clear a vent stack, do the following:

Ascend your roof with a garden shed in hand.
You should examine the top of the vent to see if there are any obstructions that may be removed by hand.
Simply insert the end of the garden hose into the vent to inspect it. There’s a chance you could free up the obstruction.
To use the garden hose, have someone activate the water supply. Most of the time, just the weight of the water is enough to clear the obstruction.
Don’t settle for water if a plumber’s snake won’t do the trick. You can also fix a blocked toilet with a local plumber if the problem is severe.
The snake must be pushed into the vent until it meets a barrier. The clog can be unhooked once the handle is cracked. To see whether there are any further obstructions, remove it and then push the snake back.
Run a flush test to see if the toilet is draining faster.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button